Modified plastics are better than general-purpose plastics in terms of flame retardancy, strength, impact resistance, toughness and other properties, and have a wide range of downstream applications...
Read More
Plasticizing components of the injection molding machine here refer to screw, melt cylinder, over rubber head, over rubber ring, over rubber washer.When the injection molding machine is working...
Read More
Product seam marks are usually caused by low temperature and low pressure at the seam line.1、Temperature problem, 1). The temperature of the barrel is too low,2). Nozzle temperature is too low.
Read More
I. What is bad gate cutting? It is a phenomenon that the gate connecting the molded products, main flow channel and manifold is not easily cut off when using point gate and other moldings...
Read More
The pump is the "heart" of all hydraulic systems. So any time there is a problem with the hydraulic system, the problem is often blamed on the pump.In fact, as far as the cause of pump damage is concerned...
Read More
The basic principle of fusible core injection molding is to first cast a fusible core using a low melting point alloy, then put the fusible core into the mold as an insert for injection molding...
Read More
In the manufacture of molds, mold exhaust is a very important part. Mold exhaust can represent the overall structure of the mold to the greatest extent.Even if the excellent mold is without good exhaust...
Read More
Advantages, Shortened cycle time, The cycle time is shortened because there is no limitation on the cooling time of the sprue system, so the part can be ejected in time after it is formed and cured...
Read More
Therefore, how to ensure the normal and stable operation of injection machines in continuous production is a problem worthy of attention and effort for both injection machine manufacturers and users.
Read More
Therefore, how to ensure the normal and stable operation of injection machines in continuous production is a problem worthy of attention and effort for both injection machine manufacturers and users.
Read More
With the wide application of plastic products, such as daily chemical products and beverage packaging containers, the appearance needs often require the surface of plastic mold cavities to reach the degree of mirror polishing.
Read More
Introduction,Except for the main flow gate, most of the gates are the smallest part of the pouring system, with a cross-sectional area of only 3% to 9% of the cross-sectional area of the manifold.
(1) the injection nozzle hole is too large to cause the melt material reflux and shrinkage, too small resistance to a large amount of material is not enough to appear shrinkage.
Read More
PVC is a heat-sensitive material, its injection molding process is poor, the reason is that too high a melt temperature or too long a heat time can easily make PVC decomposition, so controlling the melting temperature is the key to injection molding PVC p
Read More
1）Viscosity curve,The viscosity curve is made to select a suitable injection speed that will not cause large changes in melt viscosity when there are small fluctuations in each parameter. The fluctuation between each mold should be as small as possible to
Read More
1. Cavity arrangement. The number of cavities and their arrangement are determined according to the geometric structure characteristics of plastic parts, dimensional accuracy requirements, batch size, ease of mold manufacturing, mold cost, etc...
Read More
1: What is laser welding? A: Laser welding is an efficient and precise welding method that uses a high-energy-density laser beam as a heat source.
Read More
The barrel and the screw make up the extrusion system. Like the screw, the barrel works under high pressure, high temperature, severe wear and tear, and certain corrosion conditions.
Read More
For an injection molding factory, the energy consumption occupied by the injection molding process accounts for about 60%, thus effectively reducing the energy consumption of the injection molding machine is an important way to save energy in the injectio
Read More
1、Commonly used plastic engineering materials and shrinkage rate?ABS: 0.5% (super unbreakable glue),PC : 0.5% (bulletproof glass glue),PMMa ：0.5%: (plexiglass),PE ：2% polyethylene
What is the main flow channel sticking to the mold (appearance), Main runner residue is a phenomenon that the main runner of molded products fails to break away from the mold.
Read More
In the work of the mold, in addition to the requirement that the substrate has a reasonable match of high enough strength and toughness, its surface properties are crucial to the working performance and service life of the mould.
Read More
As we all know, the details determine success or failure, the best materials, even if you do not master a good detail, will be a loss. Especially fibrous PC plastic materials, in the injection molding modification process, must pay attention to the detail
Read More
Before assembly, you should carefully study and analyze the general assembly drawing. Parts diagram, to understand the role of each part, characteristics and its technical requirements, to determine the assembly benchmark.
Read More
1. Filling modification, Method: Resin + coupling agent + inorganic minerals,Commonly used materials.
Read More
